A 1500-kg sedan goes through a wide intersection traveling from north to south when it is hit by a 2200-kg SUV traveling from east to west. The two cars become enmeshed due to the impact and slide as one thereafter. On-the scene measurements show that the coefficient of kinetic friction between the tires of these cars and the pavement is 0.75, and the cars slide to a halt at a point 5.39 m west and 6.43 m south of the impact point. How fast was each car traveling just before the collision?
> A bungee cord is 30.0 m long and, when stretched a distance x, it exerts a restoring force of magnitude kx. Your father-in-law (mass 95.0 kg) stands on a platform 45.0 m above the ground, and one end of the cord is tied securely to his ankle and the othe
> A 2.8-kg block slides over the smooth, icy hill shown in Fig. P7.46. The top of the hill is horizontal and 70 m higher than its base. What minimum speed must the block have at the base of the 70-m hill to pass over the pit at the far (right hand) side of
> A 15.0-kg stone slides down a snow-covered hill (Fig. P7.45), leaving point A at a speed of 10.0 m/s. There is no friction on the hill between points A and B, but there is friction on the level ground at the bottom of the hill, between B and the wall. A
> A 28-kg rock approaches the foot of a hill with a speed of 15 m/s. This hill slopes upward at a constant angle of 40.0° above the horizontal. The coefficients of static and kinetic friction between the hill and the rock are 0.75 and 0.20, respectively. (
> A 2.0-kg piece of wood slides on a curved surface (Fig. P7.43). The sides of the surface are perfectly smooth, but the rough horizontal bottom is 30 m long and has a kinetic friction coefficient of 0.20 with the wood. The piece of wood starts from rest 4
> A car in an amusement park ride rolls without friction around a track (Fig. P7.42). The car starts from rest at point A at a height h above the bottom of the loop. Treat the car as a particle. (a) What is the minimum value of h (in terms of R) such that
> A 350-kg roller coaster car starts from rest at point A and slides down a frictionless loop-the-loop (Fig. P7.41). (a) How fast is this roller coaster car moving at point B? (b) How hard does it press against the track at point B? Fig. P7.41: Figur
> A 2.00-kg block is pushed against a spring with negligible mass and force constant k = 400 N/m, compressing it 0.220 m. When the block is released, it moves along a frictionless, horizontal surface and then up a frictionless incline with slope 37.0Â
> A block with mass 0.50 kg is forced against a horizontal spring of negligible mass, compressing the spring a distance of 0.20 m (Fig. P7.39). When released, the block moves on a horizontal tabletop for 1.00 m before coming to rest. The force constant k i
> A small block with mass 0.0400 kg is moving in the xy-plane. The net force on the block is described by the potential- energy function U(x, y)=(5.80 J/m2)x2 –(3.60 J/m3)y3. What are the magnitude and direction of the acceleration of the block when it is
> Two blocks with different masses are attached to either end of a light rope that passes over a light, frictionless pulley suspended from the ceiling. The masses are released from rest, and the more massive one starts to descend. After this block has desc
> At a construction site, a 65.0-kg bucket of concrete hangs from a light (but strong) cable that passes over a light, friction-free pulley and is connected to an 80.0-kg box on a horizontal roof (Fig. P7.37). The cable pulls horizontally on the box, and a
> You are rebuilding a 1965 Chevrolet. To decide whether to replace the flywheel with a newer, lighter-weight one, you want to determine the moment of inertia of the original, 35.6-cm-diameter flywheel. It is not a uniform disk, so you canâ€
> You are analyzing the motion of a large flywheel that has radius 0.800 m. In one test run, the wheel starts from rest and turns with constant angular acceleration. An accelerometer on the rim of the flywheel measures the magnitude of the resultant accele
> A technician is testing a computer-controlled, variable-speed motor. She attaches a thin disk to the motor shaft, with the shaft at the center of the disk. The disk starts from rest, and sensors attached to the motor shaft measure the angular acceleratio
> The Crab Nebula is a cloud of glowing gas about 10 light years across, located about 6500 light-years from the earth (Fig. P9.86). It is the remnant of a star that underwent a supernova explosion, seen on earth in 1054 A.D. Energy is released by the Cra
> A sphere with radius R = 0.200 m has density r that decreases with distance r from the center of the sphere according to r = 3.00 × 103 kg/m3 –(9.00 × 103 kg/m4)r. (a) Calculate the total mass of the sphere. (b) Calculate the moment of inertia of the sph
> A thin, uniform rod is bent into a square of side length a. If the total mass is M, find the moment of inertia about an axis through the center and perpendicular to the plane of the square.
> A dancer is spinning at 72 rpm about an axis through her center with her arms outstretched (Fig. P9.83). From biomedical measurements, the typical distribution of mass in a human body is as follows: Head: 7.0% Arms: 13% (for both) Trunk and legs: 80.0% S
> Using Problem 9.81 as a guide, apply it to a person running at 12 km/h, with his arms and legs each swinging through ±30° in 1/2 s. As before, assume that the arms and legs are kept straight. Data from Problem 9.81: If a person of mass M simply moved
> The potential energy of a pair of hydrogen atoms separated by a large distance x is given by U(x)= -C6>x6, where C6 is a positive constant. What is the force that one atom exerts on the other? Is this force attractive or repulsive?
> A baseball is thrown from the roof of a 22.0-m-tall building with an initial velocity of magnitude 12.0 m/s and directed at an angle of 53.1° above the horizontal. (a) What is the speed of the ball just before it strikes the ground? Use energy methods an
> If a person of mass M simply moved forward with speed V, his kinetic energy would be 1/2 MV2. However, in addition to possessing a forward motion, various parts of his body (such as the arms and legs) undergo rotation. Therefore, his total kinetic energy
> In Fig. P9.80, the cylinder and pulley turn without friction about stationary horizontal axles that pass through their centers. A light rope is wrapped around the cylinder, passes over the pulley, and has a 3.00-kg box suspended from its free end. There
> In the system shown in Fig. 9.17, a 12.0-kg mass is released from rest and falls, causing the uniform 10.0-kg cylinder of diameter 30.0 cm to turn about a frictionless axle through its center. How far will the mass have to descend to give the cylinder 48
> Two metal disks, one with radius R1 = 2.50 cm and mass M1 = 0.80 kg and the other with radius R2 = 5.00 cm and mass M2 = 1.60 kg, are welded together and mounted on a frictionless axis through their common center (Fig. P9.77). (a) What is the total momen
> The pulley in Fig. P9.75 has radius R and a moment of inertia I. The rope does not slip over the pulley, and the pulley spins on a frictionless axle. The coefficient of kinetic friction between block A and the tabletop is
> Exactly one turn of a flexible rope with mass m is wrapped around a uniform cylinder with mass M and radius R. The cylinder rotates without friction about a horizontal axle along the cylinder axis. One end of the rope is attached to the cylinder. The cyl
> A slender rod is 80.0 cm long and has mass 0.120 kg. A small 0.0200-kg sphere is welded to one end of the rod, and a small 0.0500-kg sphere is welded to the other end. The rod, pivoting about a stationary, frictionless axis at its center, is held horizon
> A meter stick with a mass of 0.180 kg is pivoted about one end so it can rotate without friction about a horizontal axis. The meter stick is held in a horizontal position and released. As it swings through the vertical, calculate (a) the change in gravit
> A uniform, solid disk with mass m and radius R is pivoted about a horizontal axis through its center. A small object of the same mass m is glued to the rim of the disk. If the disk is released from rest with the small object at the end of a horizontal ra
> As an intern at an engineering firm, you are asked to measure the moment of inertia of a large wheel for rotation about an axis perpendicular to the wheel at its center. You measure the diameter of the wheel to be 0.640 m. Then you mount the wheel on fri
> A force parallel to the x-axis acts on a particle moving along the x-axis. This force produces potential energy U(x) given by U(x)= ax4, where a = 0.630 J/m4. What is the force (magnitude and direction) when the particle is at x = -0.800 m?
> A uniform disk has radius R0 and mass M0. Its moment of inertia for an axis perpendicular to the plane of the disk at the disk’s center is 1/2 M0 R 2 0 . You have been asked to halve the disk’s moment of inertia by cutting out a circular piece at the cen
> It has been argued that power plants should make use of off-peak hours (such as late at night) to generate mechanical energy and store it until it is needed during peak load times, such as the middle of the day. One suggestion has been to store the energ
> A computer disk drive is turned on starting from rest and has constant angular acceleration. If it took 0.0865 s for the drive to make its second complete revolution, (a) how long did it take to make the first complete revolution, and (b) what is its ang
> While riding a multispeed bicycle, the rider can select the radius of the rear sprocket that is fixed to the rear axle. The front sprocket of a bicycle has radius 12.0 cm. If the angular speed of the front sprocket is 0.600 rev/s, what is the radius of t
> The motor of a table saw is rotating at 3450 rev/min. A pulley attached to the motor shaft drives a second pulley of half the diameter by means of a V-belt. A circular saw blade of diameter 0.208 m is mounted on the same rotating shaft as the second pull
> A vacuum cleaner belt is looped over a shaft of radius 0.45 cm and a wheel of radius 1.80 cm. The arrangement of the belt, shaft, and wheel is similar to that of the chain and sprockets. The motor turns the shaft at 60.0 rev>s and the moving belt turns t
> Engineers are designing a system by which a falling mass m imparts kinetic energy to a rotating uniform drum to which it is attached by thin, very light wire wrapped around the rim of the drum (Fig. P9.62). There is no appreciable friction in the axle of
> You must design a device for shooting a small marble vertically upward. The marble is in a small cup that is attached to the rim of a wheel of radius 0.260 m; the cup is covered by a lid. The wheel starts from rest and rotates about a horizontal axis tha
> You are designing a rotating metal flywheel that will be used to store energy. The flywheel is to be a uniform disk with radius 25.0 cm. Starting from rest at t = 0, the flywheel rotates with constant angular acceleration 3.00 rad/s2 about an axis perpen
> A disk of radius 25.0 cm is free to turn about an axle perpendicular to it through its center. It has very thin but strong string wrapped around its rim, and the string is attached to a ball that is pulled tangentially away from the rim of the disk (Fig.
> While a roofer is working on a roof that slants at 36° above the horizontal, he accidentally nudges his 85.0-N toolbox, causing it to start sliding downward from rest. If it starts 4.25 m from the lower edge of the roof, how fast will the toolbox be movi
> A roller in a printing press turns through an angle u1t2 given by
> A circular saw blade with radius 0.120 m starts from rest and turns in a vertical plane with a constant angular acceleration of 2.00 rev>s2. After the blade has turned through 155 rev, a small piece of the blade breaks loose from the top of the blade. Af
> A uniform disk with radius R = 0.400 m and mass 30.0 kg rotates in a horizontal plane on a frictionless vertical axle that passes through the center of the disk. The angle through which the disk has turned varies with time according to
> A rifle bullet with mass 8.00 g strikes and embeds itself in a block with mass 0.992 kg that rests on a frictionless, horizontal surface and is attached to a coil spring (Fig. P8.79). The impact compresses the spring 15.0 cm. Calibration of the spring sh
> A 0.150-kg frame, when suspended from a coil spring, stretches the spring 0.0400 m. A 0.200-kg lump of putty is dropped from rest onto the frame from a height of 30.0 cm (Fig. P8.78). Find the maximum distance the frame moves downward from its initial eq
> You are called as an expert witness to analyze the following auto accident: Car B, of mass 1900 kg, was stopped at a red light when it was hit from behind by car A, of mass 1500 kg. The cars locked bumpers during the collision and slid to a stop with bra
> Two blocks have a spring compressed between them, as in Exercise 8.24. The spring has force constant 720 N/m and is initially compressed 0.225 m from its original length. For each block, what is (a) the acceleration just after the blocks are released; (b
> Block B (mass 4.00 kg) is at rest at the edge of a smooth platform, 2.60 m above the floor. Block A (mass 2.00 kg) is sliding with a speed of 8.00 m/s along the platform toward block B. A strikes B and rebounds with a speed of 2.00 m/s. The collision pro
> A 5.00-kg chunk of ice is sliding at 12.0 m/s on the floor of an ice-covered valley when it collides with and sticks to another 5.00-kg chunk of ice that is initially at rest (Fig. P8.73). Since the valley is icy, there is no friction. After the collisio
> A 62.0-kg skier is moving at 6.50 m/s on a frictionless, horizontal, snow-covered plateau when she encounters a rough patch 4.20 m long. The coefficient of kinetic friction between this patch and her skis is 0.300. After crossing the rough patch and retu
> A small wooden block with mass 0.800 kg is suspended from the lower end of a light cord that is 1.60 m long. The block is initially at rest. A bullet with mass 12.0 g is fired at the block with a horizontal velocity v0. The bullet strikes the block and b
> An 8.00-kg block of wood sits at the edge of a frictionless table, 2.20 m above the floor. A 0.500-kg blob of clay slides along the length of the table with a speed of 24.0 m/s, strikes the block of wood, and sticks to it. The combined object leaves the
> You and your friends are doing physics experiments on a frozen pond that serves as a frictionless, horizontal surface. Sam, with mass 80.0 kg, is given a push and slides eastward. Abigail, with mass 50.0 kg, is sent sliding northward. They collide, and a
> Spheres A (mass 0.020 kg), B (mass 0.030 kg), and C (mass 0.050 kg) are approaching the origin as they slide on a frictionless air table. The initial velocities of A and B are given in Fig. P8.69. All three spheres arrive at the origin at the same time
> A railroad handcar is moving along straight, frictionless tracks with negligible air resistance. In the following cases, the car initially has a total mass (car and contents) of 200 kg and is traveling east with a velocity of magnitude 5.00 m/s. Find the
> Blocks A (mass 2.00 kg) and B (mass 10.00 kg, to the right of A) move on a frictionless, horizontal surface. Initially, block B is moving to the left at 0.500 m>s and block A is moving to the right at 2.00 m/s. The blocks are equipped with ideal spring b
> Three identical pucks on a horizontal air table have repelling magnets. They are held together and then released simultaneously. Each has the same speed at any instant. One puck moves due west. What is the direction of the velocity of each of the other t
> Just before it is struck by a racket, a tennis ball weighing 0.560 N has a velocity of (20.0 m/s)
> A steel ball with mass 40.0 g is dropped from a height of 2.00 m onto a horizontal steel slab. The ball rebounds to a height of 1.60 m. (a) Calculate the impulse delivered to the ball during impact. (b) If the ball is in contact with the slab for 2.00 ms
> For the Texas Department of Public Safety, you are investigating an accident that occurred early on a foggy morning in a remote section of the Texas Panhandle. A 2012 Prius traveling due north collided in a highway intersection with a 2013 Dodge Durango
> In an experiment, one of the forces exerted on a proton is
> In your job in a police lab, you must design an apparatus to measure the muzzle velocities of bullets fired from handguns. Your solution is to attach a 2.00-kg wood block that rests on a horizontal surface to a light horizontal spring. The other end of t
> A 2004 Prius with a 150-lb driver and no passengers weighs 3071 lb. The car is initially at rest. Starting at t = 0, a net horizontal force Fx(t) in the +x-direction is applied to the car. The force as a function of time is given in Fig. P8.100. (a) For
> An outlaw cuts loose a wagon with two boxes of gold, of total mass 300 kg, when the wagon is at rest 50 m up a 6.0° slope. The outlaw plans to have the wagon roll down the slope and across the level ground, and then fall into a canyon where hi
> A 12.0-kg shell is launched at an angle of 55.0° above the horizontal with an initial speed of 150 m>s. At its highest point, the shell explodes into two fragments, one three times heavier than the other. The two fragments reach the ground at the same ti
> A fireworks rocket is fired vertically upward. At its maximum height of 80.0 m, it explodes and breaks into two pieces: one with mass 1.40 kg and the other with mass 0.28 kg. In the explosion, 860 J of chemical energy is converted to kinetic energy of th
> A 20.0-kg projectile is fired at an angle of 60.0° above the horizontal with a speed of 80.0 m/s. At the highest point of its trajectory, the projectile explodes into two fragments with equal mass, one of which falls vertically with zero initial speed. I
> A 7.0-kg shell at rest explodes into two fragments, one with a mass of 2.0 kg and the other with a mass of 5.0 kg. If the heavier fragment gains 100 J of kinetic energy from the explosion, how much kinetic energy does the lighter one gain?
> In a fireworks display, a rocket is launched from the ground with a speed of 18.0 m>s and a direction of 51.0° above the horizontal. During the flight, the rocket explodes into two pieces of equal mass (see Fig. 8.32). (a) What horizontal distance from t
> You are standing on a concrete slab that in turn is resting on a frozen lake. Assume there is no friction between the slab and the ice. The slab has a weight five times your weight. If you begin walking forward at 2.00 m/s relative to the ice, with what
> A 45.0-kg woman stands up in a 60.0-kg canoe 5.00 m long. She walks from a point 1.00 m from one end to a point 1.00 m from the other end (Fig. P8.92). If you ignore resistance to motion of the canoe in the water, how far does the canoe move during this
> A 0.60-kg book slides on a horizontal table. The kinetic friction force on the book has magnitude 1.8 N. (a) How much work is done on the book by friction during a displacement of 3.0 m to the left? (b) The book now slides 3.0 m to the right, returning t
> Friends Burt and Ernie stand at opposite ends of a uniform log that is floating in a lake. The log is 3.0 m long and has mass 20.0 kg. Burt has mass 30.0 kg; Ernie has mass 40.0 kg. Initially, the log and the two friends are at rest relative to the shore
> Jonathan and Jane are sitting in a sleigh that is at rest on frictionless ice. Jonathan’s weight is 800 N, Jane’s weight is 600 N, and that of the sleigh is 1000 N. They see a poisonous spider on the floor of the sleigh and immediately jump off. Jonathan
> In beta decay, a nucleus emits an electron. A 210Bi (bismuth) nucleus at rest undergoes beta decay to 210Po (polonium). Suppose the emitted electron moves to the right with a momentum of 5.60 × 10-22 kg # m/s. The 210Po nucleus, with mass 3.50 × 10-25 kg
> A neutron at rest decays (breaks up) to a proton and an electron. Energy is released in the decay and appears as kinetic energy of the proton and electron. The mass of a proton is 1836 times the mass of an electron. What fraction of the total energy rele
> In a shipping company distribution center, an open cart of mass 50.0 kg is rolling to the left at a speed of 5.00 m/s (Fig. P8.87). Ignore friction between the cart and the floor. A 15.0-kg package slides down a chute that is inclined at 37°
> A 5.00-g bullet is shot through a 1.00-kg wood block suspended on a string 2.00 m long. The center of mass of the block rises a distance of 0.38 cm. Find the speed of the bullet as it emerges from the block if its initial speed is 450 m/s.
> A 4.00-g bullet, traveling horizontally with a velocity of magnitude 400 m/s, is fired into a wooden block with mass 0.800 kg, initially at rest on a level surface. The bullet passes through the block and emerges with its speed reduced to 190 m/s. The bl
> A 20.00-kg lead sphere is hanging from a hook by a thin wire 2.80 m long and is free to swing in a complete circle. Suddenly it is struck horizontally by a 5.00-kg steel dart that embeds itself in the lead sphere. What must be the minimum initial speed o
> A ball with mass M, moving horizontally at 4.00 m/s, collides elastically with a block with mass 3M that is initially hanging at rest from the ceiling on the end of a 50.0-cm wire. Find the maximum angle through which the block swings after it is hit.
> Two identical masses are released from rest in a smooth hemispherical bowl of radius R from the positions shown in Fig. P8.82. Ignore friction between the masses and the surface of the bowl. If the masses stick together when they collide, how high above
> A 75-kg roofer climbs a vertical 7.0-m ladder to the flat roof of a house. He then walks 12 m on the roof, climbs down another vertical 7.0-m ladder, and finally walks on the ground back to his starting point. How much work is done on him by gravity (a)
> A movie stuntman (mass 80.0 kg) stands on a window ledge 5.0 m above the floor (Fig. P8.81). Grabbing a rope attached to a chandelier, he swings down to grapple with the movie’s villain (mass 70.0 kg), who is standing directly under the chandelier. (Assu
> A 0.100-kg stone rests on a frictionless, horizontal surface. A bullet of mass 6.00 g, traveling horizontally at 350 m>s, strikes the stone and rebounds horizontally at right angles to its original direction with a speed of 250 m/s. (a) Compute the magni
> A single conservative force F1x2 acts on a small sphere of mass m while the sphere moves along the x-axis. You release the sphere from rest at x = -1.50 m. As the sphere moves, you measure its velocity as a function of position. You use the velocity data
> A long ramp made of cast iron is sloped at a constant angle u = 52.0o above the horizontal. Small blocks, each with mass 0.42 kg but made of different materials, are released from rest at a vertical height h above the bottom of the ramp. In each case the
> You are designing a pendulum for a science museum. The pendulum is made by attaching a brass sphere with mass m to the lower end of a long, light metal wire of (unknown) length L. A device near the top of the wire measures the tension in the wire and tra
> A particle moves along the x-axis while acted on by a single conservative force parallel to the x-axis. The force corresponds to the potential-energy function graphed in Fig. P7.76. The particle is released from rest at point A. (a) What is the direction
> A cutting tool under microprocessor control has several forces acting on it. One force is
> A small object with mass m = 0.0900 kg moves along the +x-axis. The only force on the object is a conservative force that has the potential-energy function U(x)= -ax2 + bx3, where a = 2.00 J/m2 and b = 0.300 J/m3. The object is released from rest at smal
> A wooden block with mass 1.50 kg is placed against a compressed spring at the bottom of an incline of slope 30.0° (point A). When the spring is released, it projects the block up the incline. At point B, a distance of 6.00 m up the incline from A, the bl
> A small rock with mass 0.12 kg is fastened to a massless string with length 0.80 m to form a pendulum. The pendulum is swinging so as to make a maximum angle of 45° with the vertical. Air resistance is negligible. (a) What is the speed of the rock when t
> You are asked to design a spring that will give a 1160-kg satellite a speed of 2.50 m/s relative to an orbiting space shuttle. Your spring is to give the satellite a maximum acceleration of 5.00g. The spring’s mass, the recoil kinetic energy of the shutt
> A small block with mass 0.0500 kg slides in a vertical circle of radius R = 0.800 m on the inside of a circular track. There is no friction between the track and the block. At the bottom of the block’s path, the normal force the track exerts on the block
> A small block with mass 0.0400 kg slides in a vertical circle of radius R = 0.500 m on the inside of a circular track. During one of the revolutions of the block, when the block is at the bottom of its path, point A, the normal force exerted on the block
